JL Audio CP112-W0V3 Subwoofer | JD1000/1 Amplifier | RBC-1 Remote Bundle – 93281 | 98363 | 98015

JL Audio CP112-WOV3 Subwoofer | JD1000/1 Amplifier | RBC-1 Remote Bundle – #93281 | 98363 | 98015

This Bundle Includes:
(1) JL Audio CP112-W0v3 BassWedge slot-ported enclosure with one 12″ W0v3 subwoofer – #93281
(1) JL Audio JD1000/1 1 Ch. 1000 Watt Subwoofer Amplifier – #98363
(1) JL Audio RBC-1 Car Audio Bass Remote Control – #98015

JL Audio CP112-W0v3 BassWedge slot-ported enclosure with one 12″ W0v3 subwoofer #93281

JL Audio built the JL Audio CP112-W0v3 enclosure to make car-rattling bass for a reasonable price, without the need for a ton of power. The enclosure’s designed to match the 12″ sub loaded into it, so you know you’ll get every ounce of performance out of this enclosure.

An excellent combination

The JL Audio CP112-W0v3 BassWedge contains one 12″ W0v3 subwoofer that handles up to 300 watts RMS, and is loaded into a specially built slot-ported enclosure. The enclosure can be placed with the woofer firing downwards, or in typical front or rear firing applications, giving you immense bass regardless of how you place it.

Solid MDF enclosure

JL Audio uses state-of-the-art automated woodworking equipment to fabricate the high-quality MDF enclosure with rugged automotive carpeting, nickel-plated push terminals, and solid internal wiring.

Features

Overview: The JL Audio CP112-W0v3 slot-ported BassWedge subwoofer enclosure is designed around JL Audio’s 12″ W0v3-4 (4″) subwoofer. Aggressive tuning delivers powerful bass without the need for a huge amplifier. The MDF enclosure is covered with gray carpet and has JL AUDIO logos embroidered across the top and front. The enclosure design offers a variety of installation options: forward, rear or down firing. The slot-port runs along the bottom of the enclosure and fires on the same plane as the woofer; the port mouth is flared to minimize air-flow noises.

Speaker Terminal: The enclosure uses one pair of nickel-plated, high current spring posts. The posts are located on the left side of the box and will accept pin connectors, single or dual banana plugs, or bare wire up to 10 gauge.

W0v3 Woofer Features:

• Dynamic Motor Analysis (DMA): DMA is JL Audio’s proprietary method of improving dynamic motor behavior. As a result of DMA optimization, the 12W0v3-4 motor displays linear force over a long excursion range, and also maintains a stable fixed magnetic field in the gap over a wide power range. The result is a reduced distortion, faithfully reproduced transients, and tight, clean, articulate bass.
• Elevated Frame Cooling: The elevated frame design of the 12W0v3-4 delivers cool air through slots directly above the top plate to the voice coil. This not only enhances power handling, but also sound quality by minimizing dynamic parameter shifts and power compression.
• Rear Gasket: The woofer has a rear gasket to provide an optimal seal when installing into the enclosure.
• Long Excursion: The subwoofer has an Xmax of 11.4mm, giving you louder bass with less distortion.

Optional Grille: The optional SGRU-12 grille (sold separately) can be added to protect the woofer cone.

Dimensions: The JL Audio CP112-W0v3 enclosure isn’t symmetrical; it’s approximately 16-1/2″ wide, 15-3/8″ tall at its tallest point (toward the front), 13-1/8″ tall at its shortest point (toward the back), 20-3/4″ deep at the base, and 16-5/8″ deep at the top.

JL Audio JD1000/1 Monoblock Class D Subwoofer Amplifier – #98363

Monoblock Class D Subwoofer Amplifier, 1000 W x 1 @ 2 ? / 600 W x 1 @ 4 ? – 14.4V

Designed to produce a serious 1000 watts into 2 ohms (14.4V, 1% THD), the JD1000/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.

The JD1000/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.

The JD1000/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.

JL Audio RBC-1 Car Audio Bass Remote Control – #98015

The JL Audio RBC-1, is a “Bass Boost” switch that activates a +6dB boost centered at 48 Hz.

JL Audio amplifiers feature bass-boost circuitry to help you adjust low-frequency impact in your vehicle. The RBC-1 wired remote bass control works with all of JL Audio’s A-Series, G-Series, RD Series, mono JX-Series, and most Slash v2 amps. You can mount the RBC-1 controller in the front of your vehicle and dial in the amount of bass you want from the driver’s seat — mounting instructions, hardware, and a 18″ cable are included.

Connect the JL Audio RBC-1 to your amp, and it converts the amp’s selectable bass boost (0 or 6 dB) to a variable boost (0 to 12 dB). With the Slash v2 amps, the RBC-1 takes the place of the amp’s boost knob, allowing you to adjust your bass boost from 0 to 15 dB. With RD Series and JX-Series mono amps, the RBC-1 controls the amp’s subwoofer level, from full mute to full volume.