Kenwood KAC-M1814 Class D 4-Channel Digital Amplifier

Product Description

Kenwood KAC-M1814 Class D 4-Channel Digital Amplifier

Kenwood KAC-M1814 Class D 4-Channel Digital Amplifier super-compact KAC-M1814 will add new clarity and impact to the basic sound system of almost any kind of vehicle on land or water, and it’ll fit in a lot of places when space is tight. This marine-rated 4-channel amp will pump up your audio system with 45 watts RMS per channel — that’s more than twice the power of most car stereos or marine receivers. The amp uses plastic covers to protect its connections and features a conformal-coated circuit board that keeps out moisture and salt, so the party won’t stop just because of a little wetness.

Works in almost any system

The Kenwood KACM1814 will accept a signal from just about any source, whether you’re using RCA cables from an aftermarket receiver or speaker wires from a factory radio. When you use the speaker-level inputs, the amplifier will sense the signal and turn itself on, so you won’t need to run a separate remote turn-on lead to the receiver or fuse box. Kenwood goes to great lengths to ensure good sound quality, putting the preamp and output power amp stages on separate circuit boards for better, cleaner performance.

signal-sensing turn-on on speaker-level inputs eliminate need for a separate remote lead

CTA-2006 compliant

Class D amp technology

variable high- and low-pass filters (50-200 Hz, 12 dB/octave)

conformal-coated circuit board — suitable for marine applications

4-Channel amplifier

One 15-amp ATM mini-fuse (installed)

Two 38″ RCA stereo patch cables

5′ Power and speaker output harness with plug cover

Four 5/8″ Screws (4x16mm)

Two 14″ Zip Ties

Two 4″ Zip Ties

2 Sets of clear self-adhesive control covers

Additional Information

Specifications	Features – Amplifier Type Class D – CEA-2006 Primary Ratings – Power Output: 45Watts RMS x 4 at 4 Ohms, ≤1%THD+N – Signal-to-Noise Ratio: 82dBA (Reference: 1Watt into 4Ohms) Maximum Power Output – MAX POWER:L 400W – RMS Power at 14.4V: A/B (2 Ohms) – 45Watts RMS x 4 at: 4 Ohms, 1kHz , ≤1% THD+N – A/B (Bridged 4Ohms): 90Watts RMS x 2 at 4 Ohms, 1kHz, ≤1%THD+N – Signal to Noise Ratio: 98dB (Reference: Rated Power into 4Ohms at 14.4V) – Frequency Response: 20Hz-20kHz (+0dB, -1dB) – Input Impedance: 10k ohm – Speaker Impedance: 4Ω ( 2Ω to 8Ω allowable) – Bridged Connection: 4Ω to 8Ω allowable – Audio Section: Low-pass Filter 50-200Hz, -12dB/oct (A/B CH) – High-pass Filter: 50-200Hz, -12dB/oct (A/B CH) – RCA Input Sensitivity: 0.2 (V) – 5.0 (V) – Speaker Level Input Sensitivity: 4.0 (V) – 12.0 (V) Terminal – Connector with DC Cable: Yes – RCA: A/B General – Dimensions(WxHxD): 145[mm] x 45 [mm] x 99 [mm] – 5-11/16 inch x 1-3/4 inch x 3-7/8 inch – Operating Voltage: 14.4V（11-16V allowable） – Current Consumption: 15 [A] – Key Features: CTA-2006 Compliant – Class: D – 2 Ohms Load Capability – Speaker Level Input – Signal Sensing Turn-on – Variable Low-Pass / High-Pass Filter Key Features – Conformal Coating – Terminal Cover – Power MOS-FET Switching Power Supply – Extruded Aluminum Heat Sink Design – A　B　Independent Gain Adjustment Accessroies – DC cable: 1.5m (5 ft) 1pc – RCA cable: 1m (3.3 ft) 2pcs – Self-tapping screws: 4x 16 mm 4pcs – Wire band: 350mm (13-3/4 inch) 2pcs – Wire band: 100mm (3-15/16 inch) 2pcs – Protective cover: 2pcs
Mobile Amplifier Channels	4 Channel
Mobile Amplifier Class	Class D
Mobile Amplifier Fuse Rating	15
Mobile Amplifier RMS	101 to 150 watts